make install problem #67
Comments
|
I'm having the same probem too! I've tried to rebuild from scratch--by downloading the nsyth-super-master here's my error-log: Makefile:40: recipe for target 'install' failed When I start up the raspi with nsyth board the power comes on--the oled displays the grid--if I move my mouse--the Grid on the monitor/Raspi software works---it moves the cursor position on the OLED--when I try moving/changing the cursor position on the trackpad--nothing happens--will check soldering---no idea why I can't build from Makefile--any trouble shooting steps or testing steps would be greatly appreciated-thanks! |
|
same problem here, is this a hardware bug? |
|
I did some debugging. My hardware seems to be fine, I verified the pin connections to the RPi and they are OK. If you need to verify check at least these connections (not testing the pots etc... just the programming interface) The RPi itself seems to be ok as well I started hacking the openocd.cfg in the thanks |
|
When cranking up the debugger using the
full output below |
|
Thanks a lot Kaosbeat for all this precisions. Today first - if I have time -:) (working) - I will try my hardware connections, specially powers and I2C, which are used to download firmware from pi. But I think problem is probably software... |
|
@cnuty where did you get your PCB? |
|
Hi Kaosbeat, |
|
same as me, I tried contacting them with this issue, no reply so far... |
|
Wow! I got my pcb from the same place too! I haven't had time to double check my hardware--but think it'll be same as either cnuty or kaosbeat--looking for another micro sd card to try software reinstall... |
|
Hi ajmonkey, |
|
Hi all,
|
|
I have similar measurements, big problem indeed ... |
|
Hi all, |
|
Hi all, |
|
I'm also having the same issue. I also purchased my board semi assembled from tindie. |
|
Hi all, |
|
I also wrote the seller on Tindie and received no reply. I haven't measured my voltage at U4,U5, U6 yet but I did check at C7 and it was bad (4.8). I'm guessing those voltage regulators could be bad... it might be worth trying to resurface mount new good ones idk. |
|
Hello @simplysnake @cnuty @kaosbeat @ajmonkey, and any other Tindie customers prior to 2018-12-3 Thank you for the feedback, we have done further testing and have confirmed the issue. As suspected, the output is not at the right voltage level because our supplier provided the wrong parts for U4,U5,U6. Instead of the TPS73133 which should output 3.3V, the boards were supplied with the TPS73150, which outputs 5V. We have received a new batch from the factory that fixes this issue, please let us know through Tindie's messaging with your order number, and we will send you a completely new board with the correct voltage regulators. You may keep your existing board if you choose to, and simply replace the voltage regulators manually for an extra nsynth. We apologize for the trouble and the inconvenience caused. If there are any further questions, please do not hesitate and reach out to us directly or through Tindie. |
|
Curious, has anyone received their replacement board yet? |
|
Hi ajmonkey, |
|
Me neither (Belgium)
but look at this possible fix #70
…On Sun, Dec 16, 2018, 08:55 cnuty ***@***.*** wrote:
Hi ajmonkey,
Not received too. But I live in France. I mail to Tindie 7 days ago et
they answered the new board shipped.
—
You are receiving this because you were mentioned.
Reply to this email directly, view it on GitHub
<#67 (comment)>,
or mute the thread
<https://github.com/notifications/unsubscribe-auth/AAMfVMkDaOJv3g7TXj2EqOqyzt-gX7I1ks5u5fxigaJpZM4YvMYR>
.
|
|
No I haven't received mine either. I'm in the US. |
|
Hi all, |
|
Is the stm32 broken after powering on with the wrong regulators?
I changed the voltage regulators on my first (faulty board) and measure 3.3V but the touch pad and pots do not work. It should be possible to change the stm32 and upload the firmware, right? |
|
Hey, sorry for backing to life this topic, but I have no idea what's going wrong after make install firmware :( sudo openocd --file openocd.cfg --command "program ../bin/main.elf verify reset exit" 0* stm32f0x.cpu cortex_m little stm32f0x.cpu unknown Makefile:40: recipe for target 'install' failed tried to resolder one voltage regulator, because he war overheating ;v |
|
Did you measure the voltage input on the chip? It should be no more than
3.3V
I think I described the pins to measure somewhere in this thread
…On Fri, Jul 26, 2019, 03:37 Tomasz Zema ***@***.***> wrote:
Hey, sorry for backing to life this topic, but I have no idea what's going
wrong after make install firmware :(
sudo openocd --file openocd.cfg --command "program ../bin/main.elf verify
reset exit"
Open On-Chip Debugger 0.10.0 (2018-12-11-16:46)
Licensed under GNU GPL v2
For bug reports, read
http://openocd.org/doc/doxygen/bugs.html
BCM2835 GPIO nums: swclk = 25, swdio = 24
BCM2835 GPIO config: srst = 23
srst_only separate srst_gates_jtag srst_push_pull connect_deassert_srst
adapter speed: 1000 kHz
adapter_nsrst_delay: 100
srst_only separate srst_nogate srst_push_pull connect_deassert_srst
cortex_m reset_config sysresetreq
srst_only separate srst_nogate srst_push_pull connect_deassert_srst
adapter_nsrst_delay: 100
adapter_nsrst_assert_width: 100
Info : BCM2835 GPIO JTAG/SWD bitbang driver
Info : SWD only mode enabled (specify tck, tms, tdi and tdo gpios to add
JTAG mode)
Info : clock speed 1001 kHz
Info : SWD DPIDR 0x00000001
Error: Could not initialize the debug port
TargetName Type Endian TapName State
------------------------------
0* stm32f0x.cpu cortex_m little stm32f0x.cpu unknown
adapter speed: 1001 kHz
Error: Could not initialize the debug port
Error: Target not examined, will not halt after reset!
TARGET: stm32f0x.cpu - Not halted
in procedure 'reset' called at file "openocd.cfg", line 22
in procedure 'ocd_bouncer'
Makefile:40: recipe for target 'install' failed
make: *** [install] Error 1
tried to resolder one voltage regulator, because he war overheating ;v
Now the temperature is ok, but still i have make install error :<
Anyone can show me please where to look for?
—
You are receiving this because you were mentioned.
Reply to this email directly, view it on GitHub
<#67?email_source=notifications&email_token=AABR6VFKGTIUI4MOEKO2TX3QBJIMHA5CNFSM4GF4YYI2YY3PNVWWK3TUL52HS4DFVREXG43VMVBW63LNMVXHJKTDN5WW2ZLOORPWSZGOD23HSAI#issuecomment-515275009>,
or mute the thread
<https://github.com/notifications/unsubscribe-auth/AABR6VHLSN4D773SSSJE3Z3QBJIMHANCNFSM4GF4YYIQ>
.
|
|
Thanks for a tip, will try tomorrow ;)
pt., 26 lip 2019 o 12:51 Kasper Jordaens <[email protected]>
napisał(a):
… Did you measure the voltage input on the chip? It should be no more than
3.3V
I think I described the pins to measure somewhere in this thread
On Fri, Jul 26, 2019, 03:37 Tomasz Zema ***@***.***> wrote:
> Hey, sorry for backing to life this topic, but I have no idea what's
going
> wrong after make install firmware :(
>
> sudo openocd --file openocd.cfg --command "program ../bin/main.elf verify
> reset exit"
> Open On-Chip Debugger 0.10.0 (2018-12-11-16:46)
> Licensed under GNU GPL v2
> For bug reports, read
> http://openocd.org/doc/doxygen/bugs.html
> BCM2835 GPIO nums: swclk = 25, swdio = 24
> BCM2835 GPIO config: srst = 23
> srst_only separate srst_gates_jtag srst_push_pull connect_deassert_srst
> adapter speed: 1000 kHz
> adapter_nsrst_delay: 100
> srst_only separate srst_nogate srst_push_pull connect_deassert_srst
> cortex_m reset_config sysresetreq
> srst_only separate srst_nogate srst_push_pull connect_deassert_srst
> adapter_nsrst_delay: 100
> adapter_nsrst_assert_width: 100
> Info : BCM2835 GPIO JTAG/SWD bitbang driver
> Info : SWD only mode enabled (specify tck, tms, tdi and tdo gpios to add
> JTAG mode)
> Info : clock speed 1001 kHz
> Info : SWD DPIDR 0x00000001
> Error: Could not initialize the debug port
> TargetName Type Endian TapName State
> ------------------------------
>
> 0* stm32f0x.cpu cortex_m little stm32f0x.cpu unknown
> adapter speed: 1001 kHz
> Error: Could not initialize the debug port
> Error: Target not examined, will not halt after reset!
> TARGET: stm32f0x.cpu - Not halted
> in procedure 'reset' called at file "openocd.cfg", line 22
> in procedure 'ocd_bouncer'
>
> Makefile:40: recipe for target 'install' failed
> make: *** [install] Error 1
>
> tried to resolder one voltage regulator, because he war overheating ;v
> Now the temperature is ok, but still i have make install error :<
> Anyone can show me please where to look for?
>
> —
> You are receiving this because you were mentioned.
> Reply to this email directly, view it on GitHub
> <
#67?email_source=notifications&email_token=AABR6VFKGTIUI4MOEKO2TX3QBJIMHA5CNFSM4GF4YYI2YY3PNVWWK3TUL52HS4DFVREXG43VMVBW63LNMVXHJKTDN5WW2ZLOORPWSZGOD23HSAI#issuecomment-515275009
>,
> or mute the thread
> <
https://github.com/notifications/unsubscribe-auth/AABR6VHLSN4D773SSSJE3Z3QBJIMHANCNFSM4GF4YYIQ
>
> .
>
—
You are receiving this because you commented.
Reply to this email directly, view it on GitHub
<#67?email_source=notifications&email_token=AJWDYFHM3PZYIZUDNNDHPSLQBLJMDA5CNFSM4GF4YYI2YY3PNVWWK3TUL52HS4DFVREXG43VMVBW63LNMVXHJKTDN5WW2ZLOORPWSZGOD24IBTQ#issuecomment-515408078>,
or mute the thread
<https://github.com/notifications/unsubscribe-auth/AJWDYFB5CZMPRYEF6HKS2VLQBLJMDANCNFSM4GF4YYIQ>
.
|
Yeah. I think it is a power issue... I got only U5 voltage regulator working properly. The others (U4 U6) won't give 3.3V don't know why :/ I guess now it's time to solve a mystery. I used this puppies https://www.ebay.com/itm/5PCS-TPS73133DBVR-IC-REG-LDO-3-3V-15A-SOT23-5-TPS73133-73133-TPS73133D-73133D-T/192825175164?ssPageName=STRK%3AMEBIDX%3AIT&_trksid=p2057872.m2749.l2649 |
|
Looks ok.
I solved the problem by using the power from the 3.3v pin on the rpi
itself....
Works perfectly now
K
…On Sat, Jul 27, 2019, 21:24 Tomasz Zema ***@***.***> wrote:
Did you measure the voltage input on the chip? It should be no more than
3.3V I think I described the pins to measure somewhere in this thread
… <#m_-7515346608150099966_>
On Fri, Jul 26, 2019, 03:37 Tomasz Zema *@*.***> wrote: Hey, sorry for
backing to life this topic, but I have no idea what's going wrong after
make install firmware :( sudo openocd --file openocd.cfg --command "program
../bin/main.elf verify reset exit" Open On-Chip Debugger 0.10.0
(2018-12-11-16:46) Licensed under GNU GPL v2 For bug reports, read
http://openocd.org/doc/doxygen/bugs.html
<http://openocd.org/doc/doxygen/bugs.html> BCM2835 GPIO nums: swclk = 25,
swdio = 24 BCM2835 GPIO config: srst = 23 srst_only separate
srst_gates_jtag srst_push_pull connect_deassert_srst adapter speed: 1000
kHz adapter_nsrst_delay: 100 srst_only separate srst_nogate srst_push_pull
connect_deassert_srst cortex_m reset_config sysresetreq srst_only separate
srst_nogate srst_push_pull connect_deassert_srst adapter_nsrst_delay: 100
adapter_nsrst_assert_width: 100 Info : BCM2835 GPIO JTAG/SWD bitbang driver
Info : SWD only mode enabled (specify tck, tms, tdi and tdo gpios to add
JTAG mode) Info : clock speed 1001 kHz Info : SWD DPIDR 0x00000001 Error:
Could not initialize the debug port TargetName Type Endian TapName State
------------------------------ 0* stm32f0x.cpu cortex_m little
stm32f0x.cpu unknown adapter speed: 1001 kHz Error: Could not initialize
the debug port Error: Target not examined, will not halt after reset!
TARGET: stm32f0x.cpu - Not halted in procedure 'reset' called at file
"openocd.cfg", line 22 in procedure 'ocd_bouncer' Makefile:40: recipe for
target 'install' failed make: *** [install] Error 1 tried to resolder one
voltage regulator, because he war overheating ;v Now the temperature is ok,
but still i have make install error :< Anyone can show me please where to
look for? — You are receiving this because you were mentioned. Reply to
this email directly, view it on GitHub <#67
<#67>?email_source=notifications&email_token=AABR6VFKGTIUI4MOEKO2TX3QBJIMHA5CNFSM4GF4YYI2YY3PNVWWK3TUL52HS4DFVREXG43VMVBW63LNMVXHJKTDN5WW2ZLOORPWSZGOD23HSAI#issuecomment-515275009>,
or mute the thread
https://github.com/notifications/unsubscribe-auth/AABR6VHLSN4D773SSSJE3Z3QBJIMHANCNFSM4GF4YYIQ
.
Yeah. I think it is a power issue... I got only U5 voltage regulator
working properly. The others (U4 U6) won't give 3.3V don't know why :/ I
guess now it's time to solve a mystery.
I used this puppies
https://www.ebay.com/itm/5PCS-TPS73133DBVR-IC-REG-LDO-3-3V-15A-SOT23-5-TPS73133-73133-TPS73133D-73133D-T/192825175164?ssPageName=STRK%3AMEBIDX%3AIT&_trksid=p2057872.m2749.l2649
—
You are receiving this because you were mentioned.
Reply to this email directly, view it on GitHub
<#67?email_source=notifications&email_token=AABR6VDX2UZIUU7TRB7JBATQBSOGXA5CNFSM4GF4YYI2YY3PNVWWK3TUL52HS4DFVREXG43VMVBW63LNMVXHJKTDN5WW2ZLOORPWSZGOD26RFMQ#issuecomment-515707570>,
or mute the thread
<https://github.com/notifications/unsubscribe-auth/AABR6VBFSWR5SSXOMKO6ARLQBSOGXANCNFSM4GF4YYIQ>
.
|
|
Something weird happens when I power MCU near C7 - raspberry shuts down :/ |
Hello,
I read all the preview posts about a "make install" problem. I reflowed the Pi interface connector and all the STM32 connections. Same error with the lite version. The message is the following:
....
_BCM2835 GPIO nums: swclk = 25, swdio = 24
BCM2835 GPIO config: srst = 23
srst_only separate srst_gates_jtag srst_push_pull connect_deassert_srst
srst_only separate srst_nogate srst_push_pull connect_deassert_srst
adapter_nsrst_delay: 100
adapter_nsrst_assert_width: 100
Info: BCM2835 GPIO JTAG/SWD bitbang driver
Info: SWD only mode enabled (specify tck, tms, tdi and tdo gpios to add JTAG mode)
Info: clock speed 1001 kHz
in procedure 'init' called at file "openocd.cfg", line 20
in procedure 'ocd_bouncer'
Makefile:40: recipe for target 'install' failed
make: *** [install] Error 1
Please, do you have an idea how I can fix it?
Thanks a lot,
Cnuty
The text was updated successfully, but these errors were encountered: