Merge branch 'main' into arduino-client

.github/.gitignore

@@ -0,0 +1,2 @@
+workflows/*
+workflows

.vscode/extensions.json

@@ -18,6 +18,12 @@
         "wokwi.wokwi-vscode",
         "moozzyk.arduino",
         "vsciot-vscode.vscode-arduino",
-        "tonybaloney.vscode-pets"
+        "tonybaloney.vscode-pets",
+        "alefragnani.bookmarks",
+        "aaron-bond.better-comments",
+        "ms-vscode.cpptools-themes",
+        "wayou.vscode-todo-highlight",
+        "gruntfuggly.todo-tree",
+        "tomoki1207.pdf"
     ]
 }

blink/blink.ino

@@ -0,0 +1,37 @@
+/*
+  Blink
+
+  Turns an LED on for one second, then off for one second, repeatedly.
+
+  Most Arduinos have an on-board LED you can control. On the UNO, MEGA and ZERO
+  it is attached to digital pin 13, on MKR1000 on pin 6. LED_BUILTIN is set to
+  the correct LED pin independent of which board is used.
+  If you want to know what pin the on-board LED is connected to on your Arduino
+  model, check the Technical Specs of your board at:
+  https://www.arduino.cc/en/Main/Products
+
+  modified 8 May 2014
+  by Scott Fitzgerald
+  modified 2 Sep 2016
+  by Arturo Guadalupi
+  modified 8 Sep 2016
+  by Colby Newman
+
+  This example code is in the public domain.
+
+  http://www.arduino.cc/en/Tutorial/Blink
+*/
+
+// the setup function runs once when you press reset or power the board
+void setup() {
+  // initialize digital pin LED_BUILTIN as an output.
+  pinMode(LED_BUILTIN, OUTPUT);
+}
+
+// the loop function runs over and over again forever
+void loop() {
+  digitalWrite(LED_BUILTIN, HIGH);   // turn the LED on (HIGH is the voltage level)
+  delay(1000);                       // wait for a second
+  digitalWrite(LED_BUILTIN, LOW);    // turn the LED off by making the voltage LOW
+  delay(1000);                       // wait for a second
+}

mc_labs/mc_lab_02/lab_test/lab_test.ino

@@ -0,0 +1,45 @@
+const int buttonPin1 =  53;
+const int buttonPin2 =  51;
+int inByte;
+
+void setup() {
+  DDRA = 0xFF;
+  PORTA = 0;
+  pinMode(buttonPin1, INPUT_PULLUP);
+  pinMode(buttonPin2, INPUT_PULLUP);
+  Serial.begin(9600);  //UART0
+}
+
+void loop() {
+  if (Serial.available()) {
+    inByte = Serial.read();
+    if (inByte == 0xA1) {
+      //Algorithm 1
+      PORTA = 1;
+      while (PORTA) {
+        delay(1000);
+        PORTA = PORTA << 1;
+      }
+    } else if (inByte == 0xA2) {
+      //Algorithm 2
+      PORTA = B10000001;
+      delay(1000);
+      PORTA = B01000010;
+      delay(1000);
+      PORTA = B00100100;
+      delay(1000);
+      PORTA = B00011000;
+      delay(1000);
+      PORTA = B00000000;
+    }
+  }
+
+  if (digitalRead(buttonPin1) == LOW) {
+    Serial.write(0xB1);
+    delay(500);
+  }
+  if (digitalRead(buttonPin2) == LOW) {
+    Serial.write(0xB2);
+    delay(500);
+  }
+}