esp-idf-st7789

ST7789 Driver for esp-idf

The demo video by Dmitry Andreev.
https://www.youtube.com/watch?v=aOyaK0pUiPk&t

Software requirements

esp-idf v4.4 or later.
This is because this version supports ESP32-C3.

Installation

git clone https://github.com/nopnop2002/esp-idf-st7789
cd esp-idf-st7789/
idf.py set-target {esp32/esp32s2/esp32s3/esp32c3}
idf.py menuconfig
idf.py flash

Note for ESP32-S2
ROM of the ESP32-S2 is small, so the tjpgd library does not exist in the ESP32-S2 ROM.
Therefore, JPEG files cannot be displayed.

Note for ESP32-C3
For some reason, there are development boards that cannot use GPIO06, GPIO08, GPIO09, GPIO19 for SPI clock pins.
According to the ESP32C3 specifications, these pins can also be used as SPI clocks.
I used a raw ESP-C3-13 to verify that these pins could be used as SPI clocks.

Configuration

You have to set this config value with menuconfig.

• CONFIG_WIDTH
• CONFIG_HEIGHT
• CONFIG_OFFSETX
• CONFIG_OFFSETY
• CONFIG_MOSI_GPIO
• CONFIG_SCLK_GPIO
• CONFIG_CS_GPIO
• CONFIG_DC_GPIO
• CONFIG_RESET_GPIO
• CONFIG_BL_GPIO

---

Generic ST7789 1.3 Inch

There is 2 kinds of marking.

MISO is not use.

BMP file

JPEG file(ESP32/ESP32-C3)

PNG file

---

Generic ST7789 1.14 Inch

---

LILYGO TTGO 1.14 Inch

---

LILYGO TTGO T8 ESP32-S2

---

JPEG Decoder

The ESP-IDF component includes Tiny JPEG Decompressor.
The document of Tiny JPEG Decompressor is here.
This can reduce the image to 1/2 1/4 1/8.

---

PNG Decoder

The ESP-IDF component includes part of the miniz library, such as mz_crc32.
But it doesn't support all of the miniz.
The document of miniz library is here.

And I ported the pngle library from here.
This can reduce the image to any size.

---

Font File

You can add your original fonts.
The format of the font file is the FONTX format.
Your font file is put in font directory.
Your font file is uploaded to SPIFFS partition using meke flash.

Please refer this page about FONTX format.

---

Font File Editor(FONTX Editor)

There is a font file editor.
This can be done on Windows 10.
Developer page is here.

This library uses the following as default fonts:

• font/ILGH16XB.FNT // 8x16Dot Gothic
• font/ILGH24XB.FNT // 12x24Dot Gothic
• font/ILGH32XB.FNT // 16x32Dot Gothic
• font/ILMH16XB.FNT // 8x16Dot Mincyo
• font/ILMH24XB.FNT // 12x24Dot Mincyo
• font/ILMH32XB.FNT // 16x32Dot Mincyo

From 0x00 to 0x7f, the characters image of Alphanumeric are stored.
From 0x80 to 0xff, the characters image of Japanese are stored.
Changing this file will change the font.

How to build your own font file

step1)
download fontxedit.exe.

step2)
download BDF font file from Internet.
I downloaded from here.
fontxedit.exe can ONLY import Monospaced bitmap fonts file.
Monospaced bitmap fonts can also be downloaded here.

step3)
import the BDF font file into your fontxedit.exe.
this tool can convert from BDF to FONTX.

step4)
adjust font size.

step5)
check font pattern.

step6)
save as .fnt file from your fontedit.exe.

step7)
upload your font file to $HOME/esp-idf-st7789/fonts directory.

step8)
add font to use

FontxFile fx32L[2];
InitFontx(fx32L,"/spiffs/LATIN32B.FNT",""); // 16x32Dot LATIN

Font file that From 0x80 to 0xff, the characters image of Japanese are stored.

Font file that From 0x80 to 0xff, the characters image of Latin are stored.

External input module

You can use these if you need some input.

• MPR121 Capacitive Touch switch
  https://github.com/nopnop2002/esp-idf-mpr121

• TTP229 Capacitive Touch switch
  https://github.com/nopnop2002/esp-idf-ttp229